EMAIL: sales@eseasongear.com
eSeasongear SALT-3000 Pool & Pond Salt Water Meter
eSeasongear SALT-3000 Pool & Pond Salt Water Meter Tester, Digital Salinity Meter for Salt Water Pool and Koi Fish Pond, SALT3000, TDS4TM-3000, TDS4TM3000 SALT 3000 Tester
Salt Range: 0-9990 ppm or 0-1%; Temperature Range: 1-50 C (display in F too, new 2017)
- Precalibrated at 3000 ppm salt (NaCl)
- Built-in ATC sensor for Automatic Temperature Compensation, 1 to 50 degrees Celsius (33 to 122 degrees Fahrenheit)
- Built-in salt (NaCl) conversion factor for meter calibration
- Works ONLY for Salt Water Pool and Koi Fish Pond Salt level testing!
- Will NOT work for Sea/Marine/Salt Water Fish Tank Salt level testing!
- Will NOT work for Food salt level testing!
- Will NOT work for any other application!
- NOT waterproof!
- Please buy the SALT-3050 if you need a waterproof salt meter.
Check out the picture to find out how to read the digital display:
300 x10 ppm = 3000ppm = 0.300% salt
The SALT-3000 is precalibrated at 3000ppm salt so there is no calibration needed.
The eSeasongear SALT-3000 is precalibrated at 3000ppm salt for pool and pond testing. This meter is equivalent to the Trans Instruments Koi Medic Salt Meter - Electronic Pond Water Salt Level Tester. The 3000ppm calibration solution is available if needed for recalibration.
*** Instruction for the SALT-3000 Meter:
1. Remove the electrode protective cap.
2. Push the ON/OFF button to turn the meter on. The reading should be 0 ppm in the air.
3. Collect water sample in a cup, immerse the electrode into the water 1 inch to maximum 2 inches
4. Lightly swirl the meter to ensure the removal of air bubbles or electric charges. Wait until the reading stabilizes. The meter automatically compensates for the temperature variations. Once the reading is stabilized (10-30 seconds), press the HOLD button to view the reading out of the water.
If you see a very small "x10" on the display, the ppm reading needs to be x10.
If you see "oor", that meanings the salt lever is over the meter testing range (0-5000ppm), please dilute your sample water 1:1 with bottled water and try it again.
5. Push the TEMP button to view the water temperature in C, push TEMP again in F, push it again will switch it back to ppm salt mode.
6. After each use, rinse the probes with bottle water, shake off water, put the cap back on, store it dry.
7. Do not touch the metal probes. Clean the probes with rubbing alcohol and a cotton swab if needed.
*** Precautions - NOT waterproof!
Do not drop the entire meter in water or dip beyond the maximum 2-inch immersion level. The SALT-3000 is not waterproof and is not covered under warranty if water or other liquid enters the meter.
Salt Range: 0-9990 ppm or 0-1%; Temperature Range: 1-50 C (display in F too, new 2017)
- Precalibrated at 3000 ppm salt (NaCl)
- Built-in ATC sensor for Automatic Temperature Compensation, 1 to 50 degrees Celsius (33 to 122 degrees Fahrenheit)
- Built-in salt (NaCl) conversion factor for meter calibration
- Works ONLY for Salt Water Pool and Koi Fish Pond Salt level testing!
- Will NOT work for Sea/Marine/Salt Water Fish Tank Salt level testing!
- Will NOT work for Food salt level testing!
- Will NOT work for any other application!
- NOT waterproof!
- Please buy the SALT-3050 if you need a waterproof salt meter.
Check out the picture to find out how to read the digital display:
300 x10 ppm = 3000ppm = 0.300% salt
The SALT-3000 is precalibrated at 3000ppm salt so there is no calibration needed.
The eSeasongear SALT-3000 is precalibrated at 3000ppm salt for pool and pond testing. This meter is equivalent to the Trans Instruments Koi Medic Salt Meter - Electronic Pond Water Salt Level Tester. The 3000ppm calibration solution is available if needed for recalibration.
*** Instruction for the SALT-3000 Meter:
1. Remove the electrode protective cap.
2. Push the ON/OFF button to turn the meter on. The reading should be 0 ppm in the air.
3. Collect water sample in a cup, immerse the electrode into the water 1 inch to maximum 2 inches
4. Lightly swirl the meter to ensure the removal of air bubbles or electric charges. Wait until the reading stabilizes. The meter automatically compensates for the temperature variations. Once the reading is stabilized (10-30 seconds), press the HOLD button to view the reading out of the water.
If you see a very small "x10" on the display, the ppm reading needs to be x10.
If you see "oor", that meanings the salt lever is over the meter testing range (0-5000ppm), please dilute your sample water 1:1 with bottled water and try it again.
5. Push the TEMP button to view the water temperature in C, push TEMP again in F, push it again will switch it back to ppm salt mode.
6. After each use, rinse the probes with bottle water, shake off water, put the cap back on, store it dry.
7. Do not touch the metal probes. Clean the probes with rubbing alcohol and a cotton swab if needed.
*** Precautions - NOT waterproof!
Do not drop the entire meter in water or dip beyond the maximum 2-inch immersion level. The SALT-3000 is not waterproof and is not covered under warranty if water or other liquid enters the meter.
Accessories
 eSeasongear SALT-3050 Waterproof Pool & Pond Salt Water Tester, Digital Salinity Meter for Salt Water Pool and Koi Fish Pond, SALT3050 SALT 3050 - Precalibrated at 3000 ppm salt (NaCl) - Built-in ATC sensor for Automatic Temperature Compensation - Built-in salt (NaCl) conversion factor for meter calibration - Salt Range: 0-9999 ppm; Temperature Range: 0-55 °C or 32-130 °F - Waterproof Rating: IP65; Do not drop the meter into water since it is not rated to the IP-67 rating. - Works ONLY for Salt Water Pool and Koi Fish Pond Salt level testing! - Will NOT work for any other application! Cross references: Hach 9531200 ($80), Hayward GLX-SALTMETER ($125), LaMotte 1749 ($90), Oakton EcoTestr CTS ($70), WD-35462-50 ($125), WD-35662-52 ($85), Ohaus ST10S ($60), ST20S ($80) Salt Meter The 3000 ppm calibration solution is available if needed for recalibration. *** Instruction for the SALT-3050 Meter: 1. Remove the electrode protective cap. 2. Push the POWER button to turn the meter on, make sure the meter is on the 0.5 ppm mode. (Push and hold the MODE button to change the mode to 0.5 ppm if needed) - New 2023 SALT-3050 is preset to the 0.5 mode already, so there is no need to set mode any more. 3. Collect water sample in a cup, immerse the electrode into the water 1 inch to maximum 2 inches (if the water sample is too cold or too hot, please let it sit at room temperature for 30 min.). 4. Lightly swirl the meter to ensure the removal of air bubbles or electric charges. Wait until the reading stabilizes. The meter automatically compensates for the temperature variations. Once the reading is stabilized (10-30 seconds), push HOLD button to view the reading out of the water. If you see "oor", that meanings the salt lever is over the meter testing range, please dilute your sample water 1:1 with bottled water and try it again. 5. Push the TEMP button to view the water temperature in C, push TEMP again for F. 6. After Use, rinse probes with DI water or bottled water, shake offer water, put the cap back on, store it dry. 7. Do not touch the metal probes. Clean the probes with a cotton swab with an acid solution if needed. 8. Email us for recalibration instruction if needed. List: $49.99 Sale: $25.99, 2/$50.00, 5/$120.00, 10/$230.00 |  eSeasongear 3000 ppm Salt NaCl Solution, 230 ml For SALT-3000 / SALT-3050 Pool & Pond salt meter calibration at 25C / 77F. List: $17.00 Sale: $14.99 |
 Spare 1.5 V Battery for eSseasongear, HANNA, HM Digital and Milwaukee Pocket pH TDS ORP Testers, Pack/10 Replacement button battery batteries for Pen style Tester Meter, SALT-3000, SALT-3050, TDS-EZ, ZT-2, TDS-3, TDS-4, COM-80, PH-80 and many more. $3.99 |
sales@eseasongear.com - We accept credit cards via PayPal, no PayPal account is required