NEW LaMotte 2056 ColorQ PRO 7 Photometer, Liquid Reagents

LaMotte R-2056 ColorQ PRO 7 (liquid) Refill Reagent Pack, R2056 for Color Q 2056 Pool Tester / Photometer.

*** This lot stock is sold out, please order the New Stock below.

1X 7038-G ALK liquid reagent for total alkalinity, 30 ml, exp. 03/2018or later 1X 7042-G CH1 liquid reagent for calcium hardness, 30 ml, exp. 03/2018 or later 1X 7041-G CH2 liquid reagent for calcium hardness, 30 ml, exp. 09/2017 or later *** The CH2 reagent has only 6 months shelf life, please buy a new one as needed. 1X P-6740-G DPD 1A liquid reagent for free chlorine, 30 ml, exp. 03/2019 or later 1X P-6741-G DPD 1B liquid reagent for free chlorine, 30 ml, exp. 03/2018 or later 1X P-6743-G DPD 3 liquid reagent for total chlorine, 30 ml, exp. 03/2019 or later 1X 7037-G pH liquid reagent for pH, 30 ml, exp. 03/2019 1X 6996A-J CYA TesTabs for Cyanuric Acid, 100/PK, exp. 04/2019 or later 6X 0201 Color Q Test Tube (5 ml)

eSeasongear SALT-3000 Pool & Pond Salt Water Meter Tester, Digital Salinity Meter for Salt Water Pool and Koi Fish Pond, SALT3000, TDS4TM-3000, TDS4TM3000 SALT 3000 Tester

Salt Range: 0-9990 ppm or 0-1%; Temperature Range: 1-50 C (display in F too, new 2017)

- Precalibrated at 3000 ppm salt (NaCl)

- Built-in ATC sensor for Automatic Temperature Compensation, 1 to 50 degrees Celsius (33 to 122 degrees Fahrenheit)

- Built-in salt (NaCl) conversion factor for meter calibration

- Works ONLY for Salt Water Pool and Koi Fish Pond Salt level testing!

- Will NOT work for Sea/Marine/Salt Water Fish Tank Salt level testing!

- Will NOT work for Food salt level testing!

- Will NOT work for any other application!

- NOT waterproof!

- Please buy the SALT-3050 if you need a waterproof salt meter.

Check out the picture to find out how to read the digital display:

300 x10 ppm = 3000ppm = 0.300% salt

The SALT-3000 is precalibrated at 3000ppm salt so there is no calibration needed.

The eSeasongear SALT-3000 is precalibrated at 3000ppm salt for pool and pond testing. This meter is equivalent to the Trans Instruments Koi Medic Salt Meter - Electronic Pond Water Salt Level Tester. The 3000ppm calibration solution is available if needed for recalibration.

*** Instruction for the SALT-3000 Meter:

1. Remove the electrode protective cap.

2. Push the ON/OFF button to turn the meter on. The reading should be 0 ppm in the air.

3. Collect water sample in a cup, immerse the electrode into the water 1 inch to maximum 2 inches

4. Lightly swirl the meter to ensure the removal of air bubbles or electric charges. Wait until the reading stabilizes. The meter automatically compensates for the temperature variations. Once the reading is stabilized (10-30 seconds), press the HOLD button to view the reading out of the water.

If you see a very small "x10" on the display, the ppm reading needs to be x10.

If you see "oor", that meanings the salt lever is over the meter testing range (0-5000ppm), please dilute your sample water 1:1 with bottled water and try it again.

5. Push the TEMP button to view the water temperature in C, push TEMP again in F, push it again will switch it back to ppm salt mode.

6. After each use, rinse the probes with bottle water, shake off water, put the cap back on, store it dry.

7. Do not touch the metal probes. Clean the probes with rubbing alcohol and a cotton swab if needed.

*** Precautions - NOT waterproof!

Do not drop the entire meter in water or dip beyond the maximum 2-inch immersion level. The SALT-3000 is not waterproof and is not covered under warranty if water or other liquid enters the meter.